Honda Acty Rear Brake Pads
$40.00
Acty rear brake shoes for HA-1/2/3/4 and HH-1/2/3/4
Vendor Information
- Store Name: WILLpowered
- Vendor: WILLpowered
- No ratings found yet!
Honda Acty Suspension Kit P-2
The P2 kit is the ultimate suspension rebuild kit for the Honda Acty at a discounted rate. This kit includes:
2 – Front struts (left and right)
2 – Rear shocks (left and right)
2 – 300 # front springs
4 – Strut rod bushings
These struts and shocks are only available at WILLpowered and slightly pressurized unlike the stock oil filled parts in your 25 year old truck or offered by others.
Honda Acty Bushings for Shifter Base
Just added is our shifter base bushings! Adding these thicker stiffer custom bushings to the base of your shifter still allows it to flex but stiffens it up for that crisper feel. Adds one minute to installation when performed with the shift kit. These will fit all HA1-4 and HH1-4 trucks and vans.
If you are ordering our shift kit you DO NOT need these as they are included in the kit.
https://youtu.be/RKchVNf5fgU?si=z0B10C02uoCVV1yz
Related products
AMP’d Microsquirt ECU
The AMP’d MicroSquirt adds higher current capacity injector drivers, higher current capacity on its optioisolated input, and 4 user configurable option switches that activate on-board pullup resistors for applications that use hall or optical style crank and cam sensors. They can also be used to re-purpose digital switch (ALED and WLED) outputs to become logic level ignition outputs for applications that require 3 or 4 ignition outputs without having to solder resistors into the ECU case or wiring.
MicroSquirt is an entry-level, fully assembled ECU with varied applications targeting power sports, single cylinder all the way up to 8 cylinders with up to 2 fuel and 4 spark outputs. Over 40 different ignition modes are supported from mainstream applications like GM LS1, Ford Zetec, Bosch Motronic, and Chrysler Gen III Hemis to unusual modes like Renix Jeep and the Suzuki Swift GTI.
We recommend using the AMP’d MicroSquirt over the regular MicroSquirt for these scenarios:
- When using 6 injectors in the 8-10 ohm range, or 8 or more injectors
- On 6 or 8 cylinder distributorless ignition applications (we make it easy to control these in wasted spark)
- 4 cylinder sequential coil on plug
- Fuel only installations triggered off the negative terminal of an ignition coil
AMP’d MicroSquirt ECU hardware features
Features in bold are added to the AMP’d MicroSquirt.
- 2 high impedance injector outputs – max peak current increased to 19 amps
- 2 dedicated spark outputs
- 2 general purpose on/off outputs – can be repurposed as spark outputs with switchable pull ups
- 1 PWM IAC output – can be repurposed as general purpose output
- 1 dedicated fuel pump output
- 2 variable reluctor conditioned inputs with switchable pull ups
- 1 optoisolated RPM input – max voltage and current increased
- 1 flex fuel or general purpose switched input
- 7 analog inputs
MicroSquirt ECU software features
- Supports speed density, alpha-N (TPS based), or MAF based fuel and spark tables
- 0.66 microsecond injector pulse width resolution
- Allows blending multiple load types, including specialized mode for independent throttle bodies
- Supports a wide variety of OEM cam and crank position sensors
- Accelerator pump or model based acceleration enrichment
- Closed or open loop idle speed and boost control
- On/off nitrous control
- Wankel rotary support: 2 rotor engines with separate leading and trailing spark tables
- Staged injection
- Table switching
- 16 x 16 fuel tables
- 12 x 12 spark tables
- 2 step rev limiter (launch control) with no-lift shifting
- Wideband AFR target table
- Flex fuel sensor input
- Real time barometric correction (external sensor required)
- Sequential shift cut and air shifter control
Honda Extended length wheel studs
Honda extended length wheel studs set of 8. Same ones that come with our big brake kit if you need longer studs to fit aftermarket rims etc. 45mm shank as opposed to the approx 25mm shank of stock studs.
UPDATE – previous studs on our site had 55mm of thread. These have 45mm thread and should be closer to what most people actually need.
WILLpowered glow face for Honda Acty
WILLpowered glow face gauges for the Honda Acty trucks and vans. These are overlays that attach with the same screws from the stock face. The gauges are set to MPH so you no longer have to convert the kmh while driving. Some twist in the face can be made to truly calibrate the speed after install but on our first try we had it within 1-2 mph and left it as is. For the tachometer face the temp and gas gauges are not lit but come with an adhesive backed piece for a matched look.
We have a new version called “No Tachometer Rounded” which is if your gas and temp gauges have rounded edges instead of a more straight down appearance. Please see pictures or call if you are not sure.
Please choose if you have a tachometer cluster or not. These will be plug and play using the dash clock harness so that the gauges will light up with your headlights. The harness will be slightly different if you have a clock already plugged in so please select if you do or don’t.